Minor repair and maintenance of engines Hyundai Elantra 1

General information and technical parameters of engines
Depending on the model and year of manufacture, the car may be equipped with engines of different displacement (1.6 l; 1.8 l; 2.0 l). 1.6L engines produced in 1992: This...

Belt/chain drives of the engine — device
All engines use belt and chain drives to drive mechanisms. •The 1.6L engine manufactured in 1992 uses: toothed belt transmission in the drive of two camshafts of the gas...

Gas distribution mechanism — device
It takes a short time for a variable valve internal combustion engine to suck in the fuel mixture and expel the exhaust gases. The camshaft cannot open the valves...

Crank mechanism — device
Pistons and cylinders In the upper third of each piston, three piston rings are placed in corresponding grooves. Under the action of spring forces, they are pressed...

Lubrication system — features of the device
In an engine, many bearings and moving parts require lubrication. Engine oil must be supplied to these areas under pressure created by the oil pump. The pump draws oil...

General description of minor repairs
Caution: This section describes some maintenance procedures and engine repairs that can be performed without removing the engine from the vehicle. Wash the engine...

Hydraulic tappets — check
• If after starting the engine a clicking sound from the hydraulic tappets appears and does not disappear as the engine warms up, check it. Extraneous noise caused by a...

Camshaft drive belt 1.6 l engine 1992 release — removal and installation
Disconnect the ground cable from the battery. Remove the alternator and power steering belts. By loosening bolt (1) and rotating bolt (2), loosen the tension of the air...

Camshaft drive belt and balance shaft drive belt for 1.6 and 1.8 L engines — removal and installation
Disconnect the ground cable from the battery. Remove the alternator and power steering belts. By loosening bolt (1) and rotating bolt (2), loosen the tension of the air...

2.0L Engine Timing Belt — Checking Tension/Adjusting
Adjustment of the toothed belt transmission tension is performed in the following sequence: Remove the servo pump V-belt (if equipped). Turn the steering wheel...

Timing Belt 2.0 Liter Engine — Replacement
Attention: To install and remove the toothed belt, it is necessary to additionally remove nearby units: generator, servo pump, air conditioning compressor. Removal Turn...

Cylinder head — replacement and installation of gasket (all engines)
The cylinder head should only be removed when the engine is cool. The intake and exhaust manifolds remain connected. A cylinder head malfunction is identified by one or...

Replacing the cylinder head gasket in 1.6L and 1.8L engines
Removal Disconnect the ground cable from the battery. Disconnect the battery with the ignition off, otherwise the injection device control unit may fail. Drain the...

Replacing the cylinder head gasket in a 2.0L engine
Cylinder head mounting elements for 2.0 liter engine 1 - cylinder block; 2 - cylinder head gasket; 3 - cylinder head; 4 - mounting bolts; 5 - gasket; 6 - cylinder head...

Camshafts of 1.6 and 1.8 liter engines — removal and installation
Removal After unscrewing the forced ventilation hose of the engine, remove the air filter. Disconnect the ignition wires and remove the ignition coils. Remove the...

2.0 liter engine camshafts — removal and installation
Removal After disconnecting the engine forced ventilation hose, remove the air filter. Remove the water pump and crankshaft pulleys. Remove the upper cover (1) of the...

Valve springs, crackers and seals — replacement (method without removing the cylinder head)
Caution: Broken valve springs and damaged valve stem seals can be replaced without removing the cylinder head. This operation usually requires special tools and a source...

Hydraulic tappet (hydraulic valve clearance compensator)
All 1.6L engines are equipped with hydraulic valve clearance compensators that automatically select valve clearances; 1.8 l and some 2.0 l engines. The gap compensator...

Valve Clearance Adjustment — 2.0 Liter Engines (2001-2005)
Elements of the gas distribution mechanism of 2.0 liter engines of 2001-2005 release A, B - adjustable gap; 1 - valve; 2 - spring; 3 - crackers; 4 - pusher; 5 -...

Intake/Exhaust Manifold — Removal and Installation
Exhaust manifold mounting elements for 1.6 and 1.8 liter engines 1 - heat-protective casing; 2 - graduate collector 3 - gasket; 4 - cylinder head. Warning: Gasoline is...

Front camshaft oil seal — replacement (2.0 liter engines)
Caution: The front camshaft oil seal can be replaced without removing the engine only if the internal components of the cylinder head are in good condition. Secure the...

Engine Brackets — Checking, Replacing and Adjusting
Engine mounts rarely require attention, however, broken or damaged mounts should be replaced immediately, otherwise the increased stress placed on engine components may...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

We recommend other sections on the topic of Hyundai manuals:

Power unit: Engine repair Hyundai Accent 3 (2005-2010)
Power unit: 2.7 liter engines Hyundai Sonata 4 (2001-2012, petrol)
Engine 2.0 and 2.4 liters: Engine repair Hyundai Santa Fe 2 (2007-2012, petrol)
Power unit: Engine repair 1.6 l Hyundai Matrix (2001-2010, petrol)

Add to social network:

Link in different formats to this section

TextHTMLBB Code

Elantra 3 (2000-2006)