Car engine cooling system Hyundai Elantra 2

Oil pressure sensor
1. If the "Oil pressure" indicator light is on when the ignition switch is in the "ON" position and turns off when the engine is starting and idling, then everything is...

Technical specifications
Cooling system - Liquid, sealed, with forced circulation of liquid, with electric fan Coolant - 6 liters Radiator - Sealed with corrugated radiator fins Radiator cap...

Checking the tightness of the system
1. Wait until the radiator has cooled down (below 38°C). Loosen the radiator cap. 2. Make sure the coolant level is at the filler neck. 3. Install a radiator cap tester...

Radiator Cap Pressure Test
1. Use an adapter to connect the plug to the device. 2. Increase the pressure until the pressure gauge needle stops moving. Valve opening pressure - 83-110 kPa (0.83-1.1...

Checking the belt tension with a device
1. Press the handle of the tension gauge and insert the belt between the spindle and the hook of the gauge. 2. Release the handle and read the measurement result on the...

Drive belt and pulleys
Removal 1. Loosen the coolant pump pulley mounting bolts. 2. Unscrew the generator support nut. 3. Loosen the generator lock bolt and remove the belt. 4. Loosen the...

Radiator — removal, inspection and installation
Removal 1. Disconnect the radiator fan motor connector. 2. Set the heater temperature control to the "hot" position. 3. Unscrew the radiator drain plug to drain the...

Radiator cap
When the pressure rises to the set level [83-110 kPa When the pressure drops to the set level [-6.86 kPa Examination 1. Check the radiator cap for damage, cracks and...

Coolant pump
Removal 1. Drain the coolant and disconnect the radiator outlet hose from the coolant pump. 2. Remove the drive belt and coolant pump pulley. 3. Remove the timing belt...

Thermostat — Removal, Checking and Installation
Tightening torque: Nm Removal and inspection 1. Drain the coolant to or below the thermostat level. 2. Remove the coolant outlet pipe and gasket. 3. Remove the...

Coolant temperature sensor
Tightening torque: Nm Removal 1. Drain the coolant to the level of the sensor or below. 2. Disconnect the negative battery cable and disconnect the connector between the...

Hoses and pipes of the cooling system
Examination Check coolant pipes and hoses for cracks, damage and restrictions. Replace if necessary. Installation 1. Install the O-ring into the groove at the end of the...

Air filter
Removal 1. Remove the hose connected to the air filter. 2. Disconnect the intake air temperature sensor wiring. 3. Disconnect the air inlet hose from the air cleaner...

Excess fuel tank and inlet pipe
Tightening torque: Nm Removal 1. Remove the idle speed control mechanism. 2. Remove the accelerator cable. 3. Remove the air hose connected to the throttle body. 4....

Silencers — removal and installation
Removal Warning. Before removing or checking the exhaust system, make sure it has cooled sufficiently. 1. Disconnect the main muffler from the center muffler. 2. Remove...

Exhaust gas cleaning system
Technical characteristics of the system System components Purpose Notes Crankcase ventilation system Positive Crankcase Ventilation (PCV) Valve Reducing hydrocarbon...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

We recommend other sections on the topic of Hyundai manuals:

Power unit: Cooling and lubrication system Hyundai Accent 3 (2005-2010)
Power unit: Cooling system Hyundai Getz (2002-2011)
Power unit: Cooling system Hyundai Sonata 3 (1993-1998)
Engine 2.7 liter: Cooling system Hyundai Santa Fe 2 (2007-2012, petrol)
Power unit: Engine cooling system Hyundai Tucson 1 (2005-2010)
Power unit: Cooling and lubrication system Hyundai Matrix (2001-2010, petrol)

Add to social network:

Link in different formats to this section

TextHTMLBB Code

Elantra 3 (2000-2006)