Repair of brake system of cars Hyundai Elantra 2

Brake system — technical characteristics
Master brake cylinder Tandem type Inner diameter 22.22 mm Brake fluid low level indicator Available Brake booster Vacuum Average diameter 233.1 mm Gain factor 4.0...

Brake system — standard parameters
Brake pedal height 190.1 mm Brake pedal travel 145 mm Gap between brake light switch housing and pedal lever 0.5-1.0 mm Brake pedal free play 3-8 mm Distance from brake...

Brake system — limit values
Front Disc Brake Pad Thickness 2.0 mm Front brake disc thickness (minimum) 20 mm Front brake disc runout 0.04 mm Drum brake lining thickness 1.5 mm Brake drum inner...

Brake system — tightening torque, Nm
Nut securing the master brake cylinder to the booster 8-12 Brake booster mounting nut 8-12 Fastening the brake cylinder hose to the manifold 8-12 Drain plug 7-13 Brake...

Brake system — malfunctions
Sign of malfunction Possible cause Method of elimination When braking, the car deviates to one side Presence of grease or oil on the surface of the brake lining...

Checking and adjusting the brake pedal
1. Pedal height Height from top of pedal to floor "A" - 190.1 mm If the pedal height does not correspond to this value, adjust it using the following recommendations: 1)...

Checking the operation of the brake booster
A simplified method for checking the performance of the brake booster is to perform the following operations: 1. Let the engine run for 1 or 2 minutes and then turn it...

Bleeding the brake system
1. Remove the brake reservoir cap and fill it with brake fluid. Warning. Avoid contact of brake fluid with painted surfaces of the vehicle body. Wash it off immediately....

Adjusting the travel of the parking brake lever
1. Pull the parking brake lever towards you with a force of approximately 196 N (20 kgf) and count the number of clicks of the lever. Parking brake lever travel (normal)...

Brake pedal
Brake pedal

Master cylinder
Master cylinder

Hydraulic brake booster
Hydraulic brake booster

Brake lines
Brake lines with ABC without ABC ABS - anti-lock braking system

Front disc brake
Front disc brake

Replacing brake pads
The brake mechanisms are equipped with wear indicators, which, when the lining thickness reaches 2 mm, begin to contact the brake disc, producing a screeching sound...

Rear drum brake
Tightening torque: Nm Removal 1. Remove the wheel, then remove the brake drum. 2. After removing the rear wheel bearing nuts, remove the hub with the brake drum. 3....

Rear disc brake
Rear disc brake Tightening torque: Nm

Parking brake
Parking brake

Anti-lock braking system — technical conditions
ABSCM (Anti-blocking system control module) Operating voltage range 9.0-16.2V Current consumption 150 mA or less Controller fuse 10A Operating temperature range from...

Anti-lock braking system — tightening torque, Nm
Sensor mounting bolt Front 7-11 Rear 17-26 Hydraulic block mounting bolt 17-26 Hydraulic Block Mounting Bracket Bolt 17-26 Six lines on the hydraulic block 13-17

Components of the ABS system
Components of the system

ABS modulator and relay
Tightening torque: Nm Removal 1. Press up on the power steering fluid reservoir. 2. Disconnect the wiring from the ABS relay box, pump motor and modulator. 3. Disconnect...

ABSCM (ABS Control Module)
Removal 1. Remove the interior trim from the trunk side. 2. Remove the ABSCM and disconnect the connector.

Wheel speed sensor
Wheel speed sensor

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

We recommend other sections on the topic of Hyundai manuals:

Chassis: Brake system Hyundai Accent 2 (1999-2005)
Chassis: Brake system Hyundai Getz (2002-2011)
Chassis: Brake system Hyundai Sonata 4 (2001-2012, petrol)
Chassis: Brake system Hyundai Santa Fe 2 (2007-2012, petrol)
Chassis: Brake system Hyundai Tucson 2 (2009-2015)
Chassis: Brake system Hyundai Matrix (2001-2010, petrol)

Add to social network:

Link in different formats to this section

TextHTMLBB Code

Elantra 3 (2000-2006)