Repair of petrol engines of the car Hyundai Elantra 2

Engine — technical characteristics
Pressure regulator Technical specifications Characteristic Nominal value Limit value General characteristics Engine type In-line, dual overhead camshaft Number of...

Checking engine oil pressure
1. Place the vehicle on a level, horizontal surface. 2. Warm up the engine. Note: If the vehicle has not been serviced for a long time, warm up the engine for...

Replacing the oil filter
Select filter All Hyundai engines are equipped with a high-quality oil filter. This filter is recommended as a replacement for all vehicles. Warning. Be careful not to...

Engine oil change
Warning. Be careful not to burn yourself, as the oil is hot. 1. Start the engine and let it run until it reaches normal operating temperature. 2. Stop the engine. 3....

Compression check
1. Before checking the compression, check the oil level in the engine sump. Make sure the starter and battery are in good condition. 2. Start the engine and wait until...

Adjusting the tension of drive belts
1. Make sure the belts are not damaged and are correctly installed in the pulley grooves. Warning. If there is noise or the belt slips, check the belt for wear, damage,...

Engine mount
Engine mount Tightening torque: Nm

Engine and gearbox assembly
Removal 1. Remove the battery. 2. Disconnect the air cleaner. 3. Disconnect the reversing light connectors and engine compartment wiring. 4. For a vehicle with a...

Camshaft belt
Tightening torque: Nm Removal 1. Remove the crankshaft pulley, water pump pulley and drive belt. 2. Remove the camshaft belt cover. 3. Remove the camshaft belt tension...

Camshaft
Tightening torque: Nm Removal 1. Disconnect the suction hose and the positive crankcase ventilation hose. 2. Remove the water pump pulley and crankshaft pulley. 3....

Cylinder head
Tightening torque: Nm Removal 1. Drain the coolant and disconnect the upper radiator hose. 2. Remove the suction hose (between the air cleaner and the rocker cover). 3....

Valves and springs
Removal 1. Using a special tool to compress the valve springs (09222-28000, 09222-29000), remove the cracker. Next, remove the upper valve spring retainer, valve spring,...

Front cover, oil pump
Tightening torque: Nm Removal 1. Remove the timing belt ( please refer to the relevant section ). 2. Remove the oil pan bolts. 3. Remove the oil pan. 4. Remove the oil...

Piston and connecting rod
Tightening torque: Nm Removal Connecting rod lower head cover Note: Keep the bearings in order according to the connecting rod numbers (in accordance with the cylinder...

Crankshaft
Tightening torque: Nm Removal 1. Remove the timing belt, front cover, wheel, cylinder head and oil pan. For details, please refer to the relevant sections. 2. Remove the...

Flywheel — removal, inspection and installation
Tightening torques: Nm: R/T: For vehicles with manual transmission; A/T: For vehicles with automatic transmission. Removal 1. Remove the drive axle in the block with the...

Cylinder block
Tightening torque: Nm Removal 1. Remove the cylinder head, timing belt, front cover, flywheel, piston and crankshaft. Examination Cylinder block 1. Visually inspect the...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

We recommend other sections on the topic of Hyundai manuals:

Power unit: Engine repair Hyundai Accent 3 (2005-2010)
Power unit: 2.0 and 2.4 liter engines Hyundai Sonata 4 (2001-2012, petrol)
Engine 2.7 liter: Engine repair Hyundai Santa Fe 2 (2007-2012, petrol)
Power unit: Engine repair 1.8 l Hyundai Matrix (2001-2010, petrol)

Add to social network:

Link in different formats to this section

TextHTMLBB Code

Elantra 3 (2000-2006)