Repair of the brake system of cars Hyundai Elantra 1

Brake operation
When the driver presses the brake pedal, a pushrod connected to the pedal presses on two pistons located one behind the other in the master cylinder. The pistons...

Checking the brakes
First, brake at low speed. Using the tire tracks on the road, check to see if the length of the tracks is the same, which indicates that the brakes are working evenly....

Brake fluid — checking and replacing
This yellowish liquid, usually toxic and aggressive to paint, is neutral to metal and rubber parts. It remains quite fluid even at 40°C and maintains this fluidity up to...

Measuring the thickness of the front disc brake pads
The front disc brakes use so-called floating caliper brake mechanisms. The brake caliper looks like a clenched fist. The brake pistons in the cylinder body press the...

Replacing the front brake pads
Removal Loosen the wheel nuts of the vehicle while it is parked on the ground. Raise the front of the vehicle and remove the front wheel, first marking the position of...

Checking the thickness/lateral runout of the front brake disc
Brake discs may be processed up to a thickness of 20 mm. If there are grooves deeper than 0.5 mm or if they are heavily worn, the brake discs must be replaced. In this...

Removal the front brake disc
Note: For more detailed information on replacing the brake disc, please refer to the chapter " Front suspension ". Brake discs must be replaced simultaneously on both...

Front Disc Brake Caliper — Disassembly and Assembly
Front Disc Brake Caliper Components (early models of the car) 1 - brake shoe; 2 - plate; 3 - bracket; 4 - finger; 5 - finger boot; 6 - bleed valve; 7 - support; 8 -...

Rear Disc Brake Pads — Removal and Installation
Rear Disc Brake Pad Mounting Elements 1 - cable; 2 - support; 3 - bracket; 4 - wear indicator; 5 - brake pads; 6 - outer plate. Removal Mark the position of the wheel...

Rear Brake Caliper — Removal and Installation
Rear wheel support mounting elements 1 - the disk is shaking; 2 - hub; 3 - support; 4 - parking brake cable; 5 - brake shield. Note: When replacing brake discs, the...

Rear Disc Brake Caliper — Disassembly and Assembly
Disassembly After removing the lower guide pin, lift the caliper bracket up (complete with brake pads, pad guides and gasket). Remove the lower guide pin bushing, lower...

Rear drum brakes
The rear wheels of the car are equipped with drum brakes, which automatically maintain the gap between the pads and the drum. Two semicircular brake shoes are pressed...

Rear wheel drum brake shoes — removal and installation
Use a plastic or rubber mallet to knock off the grease cap. Apply the parking brake and loosen the self-locking nut slightly. Mark the position of the wheel rim on the...

Rear Brake Cylinders — Removal and Installation
Removal Remove the drum brake shoes. Loosen the union nut of the brake pipe at the brake cylinder on the back side. Disconnect the brake line and seal its opening...

Wheel brake cylinder — disassembly and assembly
Elements of the working brake cylinder 1 - anther; 2 - piston; 3 - cuff; 4 - body; 5 - spring; 6 - nipple for bleeding the brake system. Disassembly Remove the dust...

Bleeding the brake system
Bleeding the brake system is required if the piping system has been opened or air has entered the system in some other way. The presence of air is manifested by the...

Adjusting the brake light switch, brake pedal height
Brake pedal mounting elements 1 - pedal; 2 - axis; 3 - bushing; 4 - spring; 5 - brake light switch. Examination Measure the height (A) of the brake pedal. Required value...

Parking brake — adjustment
Parking brake adjustment is required after replacing the parking brake lever or cable, or when the parking brake does not work. Raise the car. Check the routing and...

Brake Master Cylinder/Vacuum Booster — Removal and Installation
Removal Drain the brake fluid. Disconnect the brake pipes from the master cylinder. Disconnect the brake fluid level sensor. Remove the rear brake pressure regulator...

Master Brake Cylinder — Disassembly and Assembly
Disassembly After removing the reservoir cap, remove the diaphragm, filter, and brake fluid level sensor. Remove the float and the tank lock bolt. Remove the tank and...

Inspection and replacement of hydraulic tubes and hoses
The magnitude of pressure in hydraulic tubes is generally not determined. The test pressures for the front brakes are 100 kg/cm². These pressures are given for a cold...

Diagnostics of brake system faults
Checking the technical condition of the brake system The brake system is checked on a dry, clean and fairly level area with good coverage. Reliable check of the brake...

Anti-lock braking system (ABS)
Elements of the braking system of models with ABS 1 - rear brake mechanism; 2 - rear wheel speed sensor; 3 - brake light switch; 4 - ABS indicator light; 5 - hydraulic...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

We recommend other sections on the topic of Hyundai manuals:

Chassis: Brake system Hyundai Accent 3 (2005-2010)
Chassis: Brake system Hyundai Getz (2002-2011)
Chassis: Brake system Hyundai Sonata 3 (1993-1998)
Chassis: Brake system Hyundai Santa Fe 2 (2007-2012, petrol)
Chassis: Brake system Hyundai Tucson 1 (2005-2010)
Chassis: Brake system Hyundai Matrix (2001-2010, petrol)

Add to social network:

Link in different formats to this section

TextHTMLBB Code

Elantra 3 (2000-2006)