Brake system of the car Hyundai Accent 3

Technical characteristics of the brake system
Characteristic Nominal value Inner diameter of the master cylinder 22.22 mm Master Cylinder Piston Stroke 29-31 mm Brake force regulator response pressure 3.43 MPa Brake...

Checking the vacuum booster
1. Start the engine, let it idle for 2-3 minutes, then turn it off. 2. Press the brake pedal fully several times. If the pedal goes down the first time you press it, but...

Checking the booster check valve
1. Disconnect the booster vacuum hose (A). 2. Start the engine and let it idle. Check that a vacuum is created in the hose. If a vacuum is not created, replace the...

Checking and adjusting the brake light switch
Screw the switch until the threaded part of the plunger (A) stops in the brake pedal stop (B). Unscrew the switch by 3/4 of a turn so that the gap between the plunger...

Removal and installation the vacuum booster
1. Vacuum hose; 2. Check valve; 3. Cotter pin; 4. Gasket; 5. Hinge pin; 6. Vacuum booster; 7. Master brake cylinder; 8. Brake fluid level sensor Removal 1. Disconnect...

Removal and installation the brake hose
Removal 1. Disconnect the brake hose (1) from the brake pipe (2) by unscrewing the nut with a wrench (3). 2. Remove the clamp (4) and disconnect the brake hose (5) from...

Bleeding the brake hydraulic system
Attention: bleeding the hydraulic brake system of vehicles equipped with an anti-lock braking system (ABS) should only be carried out at specialized service stations. 1....

Removal and installation the brake pedal
1. Pedal assembly; 2. Bushing; 3. Spring washer; 4. Return spring; 5. Brake light switch; 6. Brake pedal; 7. Overlay Removal 1. Remove the lower instrument panel trim....

Removal and installation the front disc brake
1. Screw; 2. Air bleed valve; 3. Guide pin; 4. Dust cover; 5. Screw; 6. Washer; 7. Caliper bracket; 8. Brake caliper; 9. Seal; 10. Piston; 11. Piston dust cover; 12....

Removal and installation the master brake cylinder
Removal Caution: Do not allow brake fluid to come into contact with painted surfaces of the vehicle body or exposed areas of the body. If the fluid comes into contact...

Checking the proportional valve (brake force regulator)
1. Disconnect the front (1) and rear (2) brake pipes from the master cylinder (3). Connect two pressure gauges (4) to the holes of the disconnected pipes. Note: After...

Removal and installation the rear disc brake
1. Removal valve; air; 2. Brake caliper; 3. Guide pin; 4. Dust cover; 5. Piston; 6. Seal; 7. Piston dust cover; 8. Retainer; 9. Screw; 10. Washer; 11. Screw; 12. Inner...

Removal and installation the rear drum brake
1. Brake shoe support pin; 2. Gap adjuster; 3. Upper tension spring; 4. Adjustment lever; 5. Brake shoe; 6. Pressure spring; 7. Lower tension spring Removal 1. Remove...

Parking brake. Device.
1. Brake caliper; 2. Parking brake lever; 3. Contact switch; 4. Parking brake cable; 5. Brake shield; 6. Spring; 7. Expansion bar; 8. Brake shoe; 9. Guide; 10. Upper...

Removal and installation the parking brake lever
Note: The procedure for checking and adjusting the parking brake lever is described in Chapter " Maintenance ". Removal Note: Parking brake cables must not be damaged or...

Removal and installation the parking brake
Removal 1. Remove the rear wheel. Tightening torque of the nuts: 90-110 Nm. 2. Remove the brake caliper and brake disc. 3. Remove the rear wheel hub assembly (2). 4....

Checking the Parking Brake Switch
1. Remove the floor console. 2. Disconnect the connector (B) from the switch (A). 3. Check the circuit between the switch contact and ground: the parking brake lever is...

Anti-lock braking system
ABS Elements Location 1. Instrument panel (light indicator AB5/EB0); 2. Front left wheel speed sensor; 3. Hydraulic block; 4. Front right wheel speed sensor; 5. Brake...

Removal and installation the hydraulic unit
1. Exit to the anterior right branch; 2. Exit to the rear left branch; 3. Exit to the rear right branch; 4. Exit to the anterior left branch; 5. Input from the primary...

Checking the input and output signals of the ABS control unit

Removal and installation the front wheel speed sensor
1. Wiring harness connector; 2. Wheel speed sensor Removal 1. Loosen the screw (1) securing the wheel speed sensor. 2. Remove the brackets (2) of the sensor wiring...

Removal and installation the rear wheel speed sensor
1. Wiring harness connector; 2. Wheel speed sensor Removal 1. Disconnect the sensor connector (1). 2. Remove the rear seat. 3. Remove the rear side panel trim and rear...

Checking the wheel speed sensor
1. Measure the output voltage between the terminal and ground (body) by connecting the sensor as shown. Caution: To avoid damaging the sensor, be sure to include a 100...

Possible malfunctions and their causes

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

We recommend other sections on the topic of Hyundai manuals:

Chassis: Brake system Hyundai Elantra 2 (1995-2000, petrol)
Chassis: Brake system Hyundai Getz (2002-2011)
Chassis: Brake system Hyundai Sonata 4 (2001-2012, petrol)
Chassis: Brake system Hyundai Santa Fe 2 (2007-2012, petrol)
Chassis: Brake system Hyundai Tucson 1 (2005-2010)
Chassis: Brake system Hyundai Matrix (2001-2010, petrol)

Add to social network:

Link in different formats to this section

TextHTMLBB Code