Car steering Hyundai Accent 1

Technical characteristics of the steering system
Steering without power assistance Shaft - Shaft with two joints with crosspieces Steering mechanism - Rack and pinion type Rack travel - 134 mm (from stop to stop: 3.76...

Checking the steering wheel play
1. Start the engine, set the steering wheel to the position corresponding to straight-ahead movement. Turn the steering wheel by applying a force of 5 N. 2. Measure the...

Checking the rotation angle
1. Place the front wheels of the vehicle on the radius template and measure the turning angle. Rotation angle (standard value): Inner wheel - 39.7° Outside - 33.3° 2. If...

Checking the Power Steering Fluid Level
1. Place the vehicle on a level surface. 2. Start the engine. Turn the steering wheel several times, turn it continuously until the fluid temperature rises to 50-60°C....

Removal air
1. Disconnect the high-tension wire from the ignition coil side and, while operating the starter in intermittent mode (15-20 s), turn the steering wheel to the left,...

Checking the tension of the power steering belt
1. With a force of 98 N, press on the V-belt at the point indicated by the arrow and measure the deflection, comparing it with the standard value. Belt deflection...

Checking the oil pump pressure
1. Disconnect the hose from the oil pump. Connect the special tool between the oil pump and the hose. 2. Bleed the air, then start the engine and turn the steering wheel...

Steering column and shaft — removal, inspection and assembly
Tightening torques: Nm (kgf cm, lb ft) Removal and inspection 1. Remove the horn cover assembly. 2. Remove the horn plates and horn button connector. 3. Remove the...

Steering gear housing without power steering — removal, inspection and assembly
Tightening torques: Nm (kgf cm, lb ft) Removal 1. Remove the wheel with the tire. 2. Remove the connecting bolt. 3. Using a special tool (09568-31000) disconnect the...

Transverse steering rod
Tightening torques: Nm (kgf cm, lb ft)

Power Steering Housing — Removal
Tightening torques: Nm (kgf cm, lb ft) 1. Using a special tool, disconnect the tie rod end from the steering knuckle. 2. Remove the bolt connecting the universal joint...

Checking and adjusting the steering mechanism
Place the crankcase in a vice with soft jaws. Total gear preload 1. To measure the preload, rotate the pinion gear at a rate of 1 revolution per 4-6 seconds. Compare the...

Power Steering — Disassembly
1. Remove the tie rod end from the tie rod. 2. Remove the dust cover from the ball joint. 3. Remove the corrugated cover clamp. 4. Remove the corrugated cover clamp. 5....

Checking the steering gear parts
Rail 1) Check the rack toothed surface for wear or damage. 2) Check the surface in contact with the oil seal for damage. 3) Check the rack for deformation. 4) Check the...

Power Steering Housing — Assembly
Assembly is carried out in the reverse order of disassembly. In this case: 1. Apply special oil to the entire surface of the rack oil seal. Recommended Fluid - DEXRON II...

Power assisted steering oil pump
Tightening torques: Nm (kgf cm, lb ft) Removal 1. Remove the delivery hose from the oil pump. 2: Disconnect the oil drain pipe from the connector and drain the fluid. 3....

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

We recommend other sections on the topic of Hyundai manuals:

Chassis: Steering Hyundai Elantra 3 (2000-2006)
Chassis: Steering Hyundai Getz (2002-2011)
Chassis: Steering Hyundai Sonata 4 (2001-2012, petrol)
Chassis: Steering Hyundai Santa Fe 2 (2007-2012, petrol)
Chassis: Steering Hyundai Tucson 1 (2005-2010)
Chassis: Steering Hyundai Matrix (2001-2010, petrol)

Add to social network:

Link in different formats to this section

TextHTMLBB Code