Car steering Hyundai Tucson 1

Technical characteristics of the steering system

Checking the steering wheel free play
1. Set the steering wheel to the straight-ahead position and start the engine. 2. Check the steering wheel free play on its circumference. The control value of the...

Checking the wheel turning angles
1. Place the vehicle with its front wheels on the turning stand (A) and check the wheel turning angles. Control values for the wheel turning angle: internal:...

Checking the moment of resistance to rotation of the ball joint pins of the steering rod ends
1. Using a special device (09568-34000) disconnect the steering rod (A) from the steering knuckle (B). 2. Make sure that there is no excessive play in the ball joint of...

Checking the steering wheel turning force on a stationary vehicle
1. Place the car on a level horizontal surface, set the steering wheel to the straight-ahead position. 2. Increase the crankshaft speed to 1000±100 rpm. Note: After...

Checking the return of the steering wheel to the straight-ahead position
Check the steering wheel return according to the following parameters: 1. When making moderate or sharp turns, the steering wheel turning force and its return should be...

Checking the tension of the power steering pump drive belt
1. Press the drive belt in the place shown in the figure with a force of 98 N (10 kg) and measure the deflection. Normal deflection of a new drive belt: 8.8-11.0 mm; old...

Checking the fluid level in the power steering reservoir
1. Place the vehicle on a level horizontal surface. 2. Start the engine. When the vehicle is stationary, turn the steering wheel several times without interruptions to...

Replacement of working fluid
1. Raise the front of the vehicle until the wheels are off the ground and place it on stands. 2. Disconnect the drain hose from the hydraulic drive reservoir and plug...

Bleeding the power steering system
1. Disconnect the high-voltage wire from the ignition coil. Turn the starter on and off for 15-20 seconds, and turn the steering wheel five to six times in both...

Checking the power steering pump discharge pressure
1. Disconnect the high pressure hose (A) from the pump (B). Connect the pressure tester to the pump and the high pressure hose as shown in the figure. 2. Bleed the...

Steering column and steering shaft — device

Steering column and steering shaft — removal and installation
Removal 1. Disconnect the negative (-) cable from the battery terminal (A). 2. Remove the driver's airbag module (B) by unscrewing the mounting bolts (A). 3. Loosen the...

Steering column and steering shaft — checking the technical condition
1. Check the steering shaft for damage and deformation. 2. Check the shaft connections for gaps, damage and smooth movement. 3. Check the ball bearing for wear and...

Steering column and steering shaft — disassembly and assembly
Anti-theft device 1. If it is necessary to remove the anti-theft device (A), use a chisel to make a groove for a screwdriver on the heads of the special mounting bolts...

Power steering gear — device

Power Steering Gear — Removal
1. Remove the lower shaft retaining clip (A) from the driver's seat side. Remove the sound-absorbing cover (B). 2. Loosen the universal joint connecting bolts and...

Power steering — checking the technical condition and adjustment
Clamp the steering gear (A) in a vice (B) with brass or aluminum pads. Drive gear torque 1. Check the rotation torque of the drive gear by rotating it at a speed of 1...

Power steering gear — disassembly
1. Disconnect the tie rod end (A) from the tie rod (B). 2. Clamp the tie rod end (A) in a vice and remove the ball joint protective boot (B). 3. Remove the boot clamp....

Power steering gear — technical condition check
Rail Check the rack for damage, corrosion, deformation and twisting. Gear Check the gear for damage and deformation. Bearings 1. Check the bearings for jamming and noisy...

Power Steering Gear — Assembly
1. Apply power steering fluid to the entire surface of the rack seal. 2. Using the special tool, install the oil seal (A) into the steering gear housing in the position...

Power steering gear — installation
1. Install the steering gear assembly (A) into place through the right side of the vehicle. 2. Install the boot mounting plate. 3. Install the boot and secure it with a...