Exterior (external elements) of the car Hyundai Tucson 2
General information about the body Car protection 1. Cover the seats before performing any procedures to prevent contamination. 2. Cover all windows, seats and mats with heat resistant material when...
Front fender Replacement Note: Removal and installation of a cowl is made together with the assistant. Be careful not to damage the hood and body. Use the special tool to remove the...
Hood — replacement and adjustment Replacement Hood assembly replacement Note: Removal and installation of a cowl is made together with the assistant. Be careful not to damage the hood and body. Use the...
Luggage compartment door Door trim replacement Note: To avoid damage to the cladding when using a flat-blade screwdriver as a lever, wrap the screwdriver with electrical tape. Tape also adjacent...
Front door — device 1. Internal door handle body 2. Door lining 3. Internal door seal 4. Door gasket 5. Door module 6. Inner corner sector 7. Door panel 8. External door seal 9. Side door...
Adjustment of the elements of the front door Glass position adjustment Note: Inspect glass guides for damage or wear and replace if necessary. 1. Remove facing of a door. 2. Remove the door gasket. 3. Gently move...
Back door — device 1. Internal door handle body 2. Door lining 3. Internal door seal 4. Door gasket 5. Door module 6. Door panel 7. Inner triangular door cover 8. External door seal 9....
Replacing elements of the rear door Door trim replacement Note: To avoid damage to the cladding when using a flat-blade screwdriver as a lever, wrap the screwdriver with electrical tape. Tape also adjacent...
Adjustment of elements of a back door Glass position adjustment Note: Inspect glass guide grooves for damage or wear and replace if necessary. 1. Remove facing of a door. 2. Remove the door gasket. 3. Gently...
Body moldings Note: To avoid damage to the cladding when using a flat-bladed screwdriver as a lever, wrap the screwdriver with electrical tape. Tape also adjacent parts that require...
Front bumper 1. Front bumper assembly 2. Bumper beam Replacement Note: To avoid damage when using a flat-blade screwdriver as a lever, wrap the screwdriver with electrical tape. Wear...
Rear bumper 1. Rear bumper assembly 2. Bumper bracket Replacement Note: To avoid damage when using a flat-blade screwdriver as a lever, wrap the screwdriver with electrical tape....
Outside rear view mirror Replacement Note: To avoid damage to the cladding when using a flat-bladed screwdriver as a lever, wrap the screwdriver with electrical tape. Tape also adjacent parts...
Upper cross member cover Replacement 1. Remove the cover, unscrew the nut and remove the lever (A) wiper. 2. Release the clips and remove the top cover (IN) hood crossbars. 3. Installation is...
Sunroof — device 1. Panoramic sunroof frame 2. Lift arm assembly 3. Glass 4. Fairing 5. Front fixed glass 6. Electric motor 7. Rail assembly 8. Anti-impact cross member assembly...
Hatch glass replacement 1. Lower the glass. 2. Turn away bolts of fastening (A). 3. Turn away screws of fastening and remove glass (A). Attention. Do not damage the screw. 4. Installation is...
Sunroof motor replacement 1. Remove the ceiling lining. 2. Disconnect the connector (IN). 3. Loosen the motor mounting screws (A), then remove the motor. 4. Installation is carried out in the...
Hatch fairing replacement 1. Fully open the glass. 2. Using a wrench with a torx head, unscrew the screw securing the deflector (A). Attention. Do not damage the screw. 3. Turn away screws of...
Sunroof blind replacement Withdrawal 1. Remove glass. 2. Loosen the fixing screw, then remove the assembly (A) rail mechanism. Attention. Do not damage the screw. 3. Cut the tension cable to...
Replacing the front fixed sunroof glass Withdrawal 1. Remove the cover (A) roof rack with a screwdriver or a special puller. 2. Turn away fixing nuts and remove a luggage carrier (A) on the roof. 3. Remove...
Replacing the panoramic sunroof assembly Withdrawal 1. Remove the following items: A. Front seat. B. Rear seat. C. Interior trim. D. Ceiling lining. E. Roof rack and moulding. F. Front fixed glass. Note: To...
Panoramic sunroof assembly adjustment Glass alignment check 1. Check for abnormal noise or distortion during operation. 2. With the sunroof closed, check for water leakage. 3. Glass seal (IN) must be flush...
Sunroof motor initialization After discharging or disconnecting the battery, replacing or removing the fuse, you need to reset the panoramic sunroof control system as follows. 1. Turn the ignition...
Opening and closing the sunroof manually Attention. Opening and closing the sunroof manually is only allowed in emergency cases. 1. Remove the overhead console. 2. Insert the emergency handle into the hex drive...