Drive shafts and main gear of the car Hyundai Tucson 2

Drive shafts and final drive — general information
Note: BJ: Birfield constant velocity joint. TJ: Tripod type joint. VTJ: Tripod type joint.

Front drive shafts — device
1. Left drive shaft 2. Retaining ring 3. Inner shaft 4. Retaining ring 5. Right drive shaft Left drive shaft 1. Locking pin 2. Castle nut 3. Washer 4. Bierfield hinge 5....

Front Drive Shafts — Removal and Installation
1. Slightly loosen the wheel nuts. Raise the car and make sure the supports are secure. 2. Remove the front wheel (A) from the hub. Note: Tightening torque: 88.2 - 107.8...

Front Drive Shafts — Checking Technical Condition
1. Check the drive shaft boots for damage and wear. 2. Check the drive shaft splines for wear or damage. 3. Make sure that no water or other foreign materials enter the...

Front Drive Shafts — Disassembly
Attention. Do not disassemble the Bierfield joint. The drive shaft joint must be coated with a special lubricant. It must not be replaced with another type of lubricant....

Front Drive Shafts — Assembly
1. To avoid damaging the anthers, wrap the splines (VTJ joint) of the drive shaft with tape. 2. Install the BJ (Bearfield) joint boot, having previously lubricated it...

Rear drive shafts — device
1. Subframe 2. Shock absorber 3. Spring 4. Upper arm 5. Trailing arm 6. Drive shaft 7. Main gear housing 1. Locking pin 2. Castle nut 3. Washer 4. Phonic wheel 5....

Rear Drive Shafts — Removal and Installation
1. Loosen the wheel nuts slightly. Raise the rear of the car and place stands to secure it. 2. Remove the rear wheel from the hub. Caution: When removing the rear wheel...

Rear Drive Shafts — Checking Technical Condition
See the steps described for front drive shafts .

Rear Drive Shafts — Disassembly
Attention. Do not disassemble the constant velocity joint. The drive shaft joint must be coated with a special lubricant. It must not be replaced with another type of...

Rear Drive Shafts — Assembly
1. Wrap tape around the drive shaft splines (tripod joint side) to prevent damage to the boots. 2. Apply grease to the drive shaft and install the dust boots. 3. Apply...

Front axle
1. Locking pin 2. Drive shaft nut 3. Brake disc 4. Hub 5. Wheel bearing 6. Retaining ring 7. Dust cover 8. Steering knuckle 9. Drive shaft Removal and installation 1....

Rear axle
1. Wheel support 2. Parking brake 3. Hub assembly 4. Brake disc Removal and installation 1. Perform steps 1-12 in the "Removing and installing rear drive shafts"...

Cardan shaft
1. Front part of the propeller shaft 2. Support bearing bracket 3. Rear part of the propeller shaft Checking the technical condition CV joints and dust boots 1. Shift...

Main gear
1. Pinion nut 2. Connecting flange 3. Front oil seal 4. Front drive pinion bearing 5. Main gear housing 6. Gasket 7. Filler plug 8. Lateral seal 9. Drain plug 10. Gasket...

Tightening torques
Caution: Replace the self-locking nuts with new ones after each removal.

Lubricants

Special tools and devices

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

We recommend other sections on the topic of Hyundai manuals:

Transmission: Drive shafts Hyundai Accent 1 (1994-1999)
Transmission: Drive shafts Hyundai Elantra 1 (1990-1995, petrol)
Transmission: Drive shafts and axles Hyundai Getz (2002-2011)
Transmission: Drive shafts Hyundai Sonata 4 (2001-2012, petrol)

Add to social network:

Link in different formats to this section

TextHTMLBB Code