Heating, ventilation and air conditioning Hyundai Accent 3

Replacement of refrigerant and compressor oil
Coolant It is recommended that the refrigerant be removed at specialized service stations using special filling stations connected to the service valves of the high (1)...

Removal and installation the compressor
1. Screw; 2. Anchor disk; 3. Washer; 4. Fastening ring; 5. Pulley; 6. Retaining ring; 7. Electromagnetic clutch; 8. Screw; 9. Bracket; 10. Compressor; 11. Collector; 12....

Removal, installation and testing of the electromagnetic clutch
Removal 1. Hold the armature disc/hub with a suitable puller and loosen the screw (1). Tightening torque: 10-15 Nm. 2. Remove the anchor disk (2) and adjusting washers...

Removal and installation the condenser
Removal 1. Disconnect the wire from the negative terminal of the battery. 3. Remove the refrigerant from the air conditioner. 3. Remove the radiator. 4. Unscrew the two...

Replacing the filter-drier
1. Remove the condenser and unscrew the plug (1) with a suitable wrench (2). Tightening torque: 20-25 Nm. 2. Remove the filter drier (3) using tweezers. 3. Insert the...

Removal, installation and checking the refrigerant pressure sensor
Removal 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the refrigerant from the air conditioner. 3. Disconnect the pressure (1) and feed (2)...

Removal, installation and checking the evaporator temperature sensor
Removal 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the right floor console trim (1). 3. Disconnect the sensor connector (2). 4. Turn the...

Removal, installation and checking the air temperature and humidity sensor
Removal 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the air conditioning control unit. 3. Unscrew the two screws (1) and remove the...

Removal, installation and testing of the solar radiation intensity sensor
Removal 1. Disconnect the wire from the negative terminal of the battery. 2. Using a screwdriver, remove the sensor (B) from the windshield deflector (A). Installation...

Removal, installation and checking the water temperature sensor
Removal 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the right floor console trim (1). 3. Disconnect the sensor connector (2). 4. Remove...

Removal, installation and checking the ambient air temperature sensor
Removal 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the front bumper. 3. Remove the ambient air temperature sensor (A). Installation 4....

Removal and installation the heater
1. Body (left side); 2. Body (right side); 3. Heater radiator; 4. Evaporator; 5. Evaporator temperature sensor; 6. Heat shield; 7. Gasket; 8. Temperature damper; 9....

Removal, installation and testing of the temperature flap drive
Removal 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the right floor console trim (1). 3. Disconnect the drive connector (2). Loosen the...

Removal, installation and inspection of the air distribution drive
Removal 1. Disconnect the wire from the negative terminal of the battery 2. Remove the pins and remove the left floor console trim (1). 3. Disconnect the drive connector...

Removal and installation the fan
1. Body (upper part); 2. Body (lower part); 3. Air intake (left side); 4. Air intake (right side); 5. Intake flap; 6. Intake flap lever; 7. Intake flap drive; 8. Air...

Removal, installation and testing of the fan electric motor
Removal 1. Disconnect the cable from the negative terminal of the battery. 2. Disconnect the electric motor connector (1). 3. Unscrew the screws and remove the electric...

Removal, installation and testing of the power transistor
Removal 1. Disconnect the wire from the negative terminal of the battery. 2. Disconnect the connector (1) of the power transistor. 3. Unscrew the screws (2) and remove...

Removal, installation and checking the fan resistor
Removal 1. Disconnect the wire from the negative terminal of the battery. 2. Disconnect the fan resistor connector (A). Loosen the screws and remove the resistor (B)....

Removal, installation and testing of the intake valve drive
Removal 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the glove box. 3. Disconnect the drive connector (A). Loosen the screws and remove...

Removal and installation the air conditioning control unit
Removal 1. Disconnect the wire from the negative terminal of the battery. 2. Use a screwdriver to release the clamps and remove the air conditioning control unit. 3....

Reading air conditioner fault codes
1. Turn on the ignition. 2. While holding the "AUTO" button, press the "OFF" button within 2 seconds at least 4 times. 4. Read the two-digit code on the display. 3. Make...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

We recommend other sections on the topic of Hyundai manuals:

Electrical equipment: Heating and air conditioning Hyundai Elantra 1 (1990-1995, petrol)
User manual: Heating and ventilation Hyundai Getz (2002-2011)
Body: Heater and air conditioner Hyundai Sonata 4 (2001-2012, petrol)
User manual: Heating and ventilation Hyundai Santa Fe 2 (2007-2012, petrol)
Body: Heater and air conditioner Hyundai Matrix (2001-2010, petrol)

Add to social network:

Link in different formats to this section

TextHTMLBB Code