Dual camshaft (DOHC) engines Hyundai Accent 1
Repair procedures for gasoline 4-cylinder engines with a volume of 1.5 liters with two overhead camshafts of Hyundai Accent cars of the first generation from 1994 to 1999 of release.
Replacement of oil filter, oil and compression test
The operations for replacing the oil filter, engine oil and checking the compression in the cylinders of an engine with two camshafts are similar to similar operations...
The operations for replacing the oil filter, engine oil and checking the compression in the cylinders of an engine with two camshafts are similar to similar operations...
Adjusting the tension of drive belts
1. Make sure the belts are not damaged and are correctly installed in the pulley grooves. 2. Apply a force of 100 N to the middle part of the belt between the pulleys as...
1. Make sure the belts are not damaged and are correctly installed in the pulley grooves. 2. Apply a force of 100 N to the middle part of the belt between the pulleys as...
Engine and gearbox assembly
Operations for fastening a twin cam engine, as well as for removing and installing the unit " Engine and gearbox " are similar to those given in this chapter above for a...
Operations for fastening a twin cam engine, as well as for removing and installing the unit " Engine and gearbox " are similar to those given in this chapter above for a...
Timing belt — removal, inspection and installation
The operations for removing, checking and installing the timing belt for twin camshaft engines are similar to those given earlier in this chapter for single camshaft...
The operations for removing, checking and installing the timing belt for twin camshaft engines are similar to those given earlier in this chapter for single camshaft...
Camshafts — removal, inspection and installation
Removal 1. Disconnect the suction hose and PCV (positive crankcase ventilation) hose. 2. Remove the water pump pulley and crankshaft pulley. 3. Remove the timing belt...
Removal 1. Disconnect the suction hose and PCV (positive crankcase ventilation) hose. 2. Remove the water pump pulley and crankshaft pulley. 3. Remove the timing belt...
Cylinder head — removal, inspection and installation
The operations for removing, checking and installing the cylinder head for engines with two camshafts are similar to those given earlier in this chapter for engines with...
The operations for removing, checking and installing the cylinder head for engines with two camshafts are similar to those given earlier in this chapter for engines with...
Valves and valve springs — removal, inspection and installation
Removal 1. Using a special tool to compress valve springs (09222-28000, 09222-28100), remove the cracker. Next, remove the upper valve spring plate, valve spring, lower...
Removal 1. Using a special tool to compress valve springs (09222-28000, 09222-28100), remove the cracker. Next, remove the upper valve spring plate, valve spring, lower...
Front cover, oil pump — removal, inspection and installation
The operations for removing, checking and installing the front cover and oil pump are similar to those given earlier in this chapter for engines with one camshaft.
The operations for removing, checking and installing the front cover and oil pump are similar to those given earlier in this chapter for engines with one camshaft.
Piston and connecting rod — removal, inspection and installation
The operations for removing, checking and installing pistons and connecting rods are similar to those given earlier in this chapter for engines with one camshaft.
The operations for removing, checking and installing pistons and connecting rods are similar to those given earlier in this chapter for engines with one camshaft.
Crankshaft — removal, inspection and installation
The operations for removing, checking and installing the crankshaft are similar to those given earlier in this chapter for engines with one camshaft.
The operations for removing, checking and installing the crankshaft are similar to those given earlier in this chapter for engines with one camshaft.
Flywheel — removal, inspection and installation
The operations for removing, checking and installing the flywheel are similar to those given earlier in this chapter for engines with one camshaft.
The operations for removing, checking and installing the flywheel are similar to those given earlier in this chapter for engines with one camshaft.
Cylinder Block — Removal and Inspection
The operations for removing, checking and installing the cylinder block are similar to those given earlier in this chapter for engines with one camshaft.
The operations for removing, checking and installing the cylinder block are similar to those given earlier in this chapter for engines with one camshaft.
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
We recommend other sections on the topic of Hyundai manuals:
Power unit: Engine repair 1.5/1.6 l Hyundai Getz (2002-2011)
Power unit: Engine repair I4 DOHC Hyundai Sonata 3 (1993-1998)
Link in different formats to this section
TextHTMLBB Code
- General information
- User manual
- Maintenance
- Power unit
- Engine repair
- Cooling and lubrication system
- Power and exhaust system
- Engine electrical equipment
- Engine management
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Chassis
- Front suspension
- Rear suspension
- Wheels and tires
- Steering
- Brake system
- Body
- Exterior (external elements)
- Interior (internal elements)
- Heating and ventilation
- Electrical equipment
- Equipment and devices
- Electrical circuits
- User manual
- Control devices
- Starting engine and driving
- Troubleshooting
- Power unit
- SOHC engines
- DOHC engines
- Lubrication system
- Cooling system
- Decreased toxicity
- Fuel system
- Ignition system
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Axles and drive shafts
- Chassis
- Car suspension
- Steering
- Brake system
- Body
- Exterior (external elements)
- Interior (internal elements)
- Air conditioning system
- Electrical equipment
- Equipment and devices
- Power devices
- General information
- Maintenance
- Power unit
- SOHC engines
- DOHC engines
- Cooling system
- Intake and exhaust systems
- Fuel supply (1.3 l, injection)
- Fuel supply (1.5 l, injection)
- Fuel supply (carburetor)
- Transmission
- Clutch
- Manual gearbox
- Automatic gearbox
- Drive shafts
- Chassis
- Car suspension
- Steering
- Brake system
- Body
- Body elements
- Electrical equipment
- Equipment and devices
- Electrical circuits