1.5 and 1.6 liter DOHC engine repair Hyundai Getz

1.5 and 1.6 liter DOHC engine specifications
Front view of the engine: 1 - protective screen of the catalytic collector; 2 - catalytic collector; 3 - oxygen concentration sensor; 4 - oil pan; 5 - oil filter; 6 -...

Checking the compression in the cylinders
If the Hyundai Getz engine is running poorly or intermittently, check the ignition system and fuel system. If the reasons for poor engine performance cannot be found,...

Timing belt — removal and installation
Removal 1. Raise the vehicle. 2. Unscrew the 14 mm bolt, three nuts and remove the engine support bracket. 3. Remove the water pump pulley mounting bolts. 4. Loosen the...

Adjusting the timing belt tension
1. Turn the steering wheel fully counterclockwise. Note: Do not apply too much force when turning the steering wheel. 2. Raise the car. 3. Unscrew the 14 mm bolt, three...

Adjusting the tension of the poly V-belt
1. Check the condition of the poly V-belt and its position on the pulleys. 2. Check the belt tension by applying 100 N of force to it at a location equidistant from the...

Adjusting the alternator drive belt tension
Caution! If the belt is loose, it will make extraneous noise during operation and will be subject to premature wear. If the belt is too tight, damage to the water pump...

Engine Mounts — Removal and Installation
Removal Attach the lifting mechanism clamps to the Hyundai Getz engine eyes and lift so that the engine weight is supported by the lifting mechanism. 1. Disconnect the...

Air filter — removal and installation
Removal 1. Remove the air intake pipe connected to the air filter. 2. Remove the air intake hose from the air filter side. 3. Remove the air filter cover and air filter...

Camshafts — Removal and Installation
Removal 1. Disconnect the crankcase ventilation hose. 2. Remove the water pump pulley and crankshaft. 3. Remove the timing belt cover. 4. Move the timing belt tension...

Cylinder head repair
Disassembly 1. Using a special tool, in the sequence shown in the figure, in 2–3 passes, unscrew the cylinder head mounting bolts. 2. Using the special tool, compress...

Exhaust manifold — removal and installation
Removal 1. Disconnect the connector from the oxygen sensor. 2. Remove the exhaust manifold heat shield. 3. Remove the exhaust manifold from the cylinder head. 4. Remove...

Intake manifold — removal and installation
Removal 1. Disconnect the connectors from the absolute pressure sensors, idle air control valve and throttle position sensor of Hyundai Getz. 5. Disconnect the coolant...

Removal and installation of engine and gearbox
Removal Warning! When removing the power unit, ensure that the jacks and stands are installed correctly and that the engine is securely fastened with the slings of the...

Cylinder Block — Removal and Inspection
Removal 1. Remove the timing belt, cylinder head, front cover, flywheel, pistons with connecting rods and crankshaft. 2. Using special tool 09260–32000, remove the oil...

Flywheel — removal and installation
Removal 1. Remove the gearbox and clutch. 2. Remove the bolts and flywheel. If the Hyundai Getz has an automatic transmission, remove the drive disk. When removing the...

Crankshaft — removal and installation
Removal 1. Remove the timing belt, front cylinder block cover, flywheel, cylinder head and oil pan. 2. Remove the rear cover from the cylinder block and the rear...

Pistons and connecting rods — removal and installation
Removal Connecting rod cap Caution: Keep the connecting rod caps with the corresponding connecting rods for proper reinstallation into the engine cylinders. 1. Unscrew...

Exhaust system — removal and installation
Removal Main muffler Warning: Make sure the exhaust system is sufficiently cool before removing or inspecting components. 1. Disconnect the main muffler from the center...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

We recommend other sections on the topic of Hyundai manuals:

Power unit: DOHC engines Hyundai Accent 1 (1994-1999)
Power unit: Engine repair I4 DOHC Hyundai Sonata 3 (1993-1998)

Add to social network:

Link in different formats to this section

TextHTMLBB Code