Car air conditioner and heater Hyundai Getz

Air conditioning and ventilation system
Air flow diagram in the ventilation, heating and air conditioning system: 1 - windshield blower deflectors; 2 - air flow distribution flaps to the windshield deflectors...

Instructions for use of refrigerant
1. Liquid refrigerant R-134a with a high content of volatile substances. If it gets on your skin, it can result in frostbite, so when working with the refrigerant, you...

Notes when replacing air conditioning system components
1. Never open the circuit or disconnect any components of the Hyundai Getz air conditioning system before discharging the system. 2. After disconnecting the air...

Connecting the elements of the air conditioning system
1. Bolted connections. 1) To facilitate tightening and ensure tightness of connections, lubricate all fasteners with compressor oil before assembly. 2) To prevent...

Air Conditioning Compressor Lubricant Oil
Air conditioning compressor lubricating oil circulates in the system when the compressor is running. When replacing any component of the air conditioning system with a...

Topping up compressor oil when replacing parts
When replacing air conditioning system components, make sure to add only the specified amount of oil. Volume of oil to be added during replacement: Evaporator: 90 cm³...

Installation of pressure gauges to measure pressure
Attention! When installing pressure gauges to measure pressure on Hyundai Getz, observe safety precautions. 1. Close both gauge adapter valves. 2. Connect the filling...

Discharging the air conditioning system
1. Connect a pressure gauge to the air conditioning system to measure pressure. 2. Place a towel under the open end of the center hose. 3. Slowly open the high pressure...

Pumping atmospheric air out of the air conditioning system
Note: If the air conditioning circuit has been opened and atmospheric air has entered it, it must be evacuated using a vacuum pump. After installing an air conditioning...

Connecting the inlet valve to the refrigerant cylinder
1. Before connecting the valve to the container, turn the handle fully counterclockwise. 2. Turn the handle counterclockwise until it reaches the highest position. 3....

Charging the system with refrigerant vapor
Note: The air conditioning system must be charged with refrigerant in gaseous state through the low pressure side. When the cooling container is placed on the right...

Charging the system with liquid refrigerant
Note: The air conditioning system must be charged with refrigerant in liquid state through the high pressure side. When the container is upside down, the refrigerant...

Checking the air conditioning system for leaks
In all cases where a refrigerant leak is suspected or work has been carried out involving disconnecting components or loosening connections, perform a leak test of the...

Tensioning the poly V-belt of the air conditioning compressor drive
State Belt deflection, mm New belt 5,0–5,5 Used belt 6–7 After use 8

Performance testing
1. Install pressure gauges on the line. 2. Start the engine, let it run at 2000 rpm⁻¹ and set the maximum cooling mode with high fan speed. 3. Open all windows or doors....

Air conditioning system air filter
1. Open the glove box, remove the glove box latch at the bottom of the instrument panel on the passenger side, and lower the glove box to its lowest position. 2....

Evaporator — removal and installation
Removal 1. Discharge the air conditioning system. 2. Disconnect the air conditioner suction hose, liquid refrigerant pipe and remove the seal. 4. Pull the center panel...

Air Conditioning Compressor — Removal and Installation
Removal 1. Discharge the air conditioning system. 2. Loosen the tension roller mounting bolt and remove the compressor drive belt. 4. Remove the four air conditioning...

Clutch hub and compressor pulley
Removal 1. Unscrew the clutch sleeve mounting bolt, while using a special key to hold the sleeve from turning. 2. Remove the clutch hub and adjusting lining from the...

Compressor coil — removal and installation
Removal 1. Remove the clutch hub and air conditioner compressor pulley. 2. Install the safety tool on the open hole of the compressor shaft. 3. Install the pulley on the...

Compressor shaft seal — removal and installation
Removal To replace the compressor shaft seal, drain the air conditioning system of refrigerant and remove the compressor. 1. Remove the clutch hub from the compressor....

Condenser — removal, inspection and installation
Removal 1. Discharge the air conditioning system from refrigerant, disconnect the hose from the radiator and drain the coolant. 2. Unscrew the two bolts and remove the...

Triple pressure sensor
The triple pressure switch is a combination switch for low pressure (to turn off the compressor when the refrigerant pressure is low), medium pressure (to prevent...

Heater — removal and installation
The heat generated by the engine is transferred by the coolant to the heater radiator located in the passenger compartment. The air flow supplied by the ventilation...

Heater Fan — Removal, Checking and Installation
Removal 1. Disconnect the two drive cables from the heater and one drive cable from the fan housing. Heater Fan: 1 - guide casing; 2 - fan casing; 3 - air intake damper...

Heater control panel
Removal 1. Disconnect the two drive cables from the heater and one drive cable from the fan housing. Heater control unit: 1 - panel overlay; 2 - control panel; 3 -...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

We recommend other sections on the topic of Hyundai manuals:

Body: Air conditioning system Hyundai Accent 2 (1999-2005)
Body: Air conditioning system Hyundai Elantra 3 (2000-2006)
Body: Air conditioning and heater Hyundai Tucson 1 (2005-2010)

Add to social network:

Link in different formats to this section

TextHTMLBB Code