Car suspension and wheels Hyundai Getz

Car Suspension Specifications
Technical data Front suspension: Type - MacPherson with coil spring Front suspension shock absorber Type Hydraulic Stroke, mm 143 Damping at acceleration 0.3 m/s —...

Special tools and devices for chassis repair
Spare parts and accessories catalogue number Name Application 0953-11600 Devices for checking the moment of resistance to rotation of the pins of the ball joints and...

Suspension and chassis faults
Cause of malfunction Method of elimination Steering wheel is hard to turn Front wheel alignment misalignment Adjust Excessive resistance to turning of the ball joint pin...

Front suspension device
Front suspension elements: 1 - wheel hub; 2 - shock absorber strut; 3 - spring; 4 - upper support of the shock absorber strut; 5 - transverse stabilizer bar; 6 - Front...

Removal and installation the front suspension strut
Telescopic front suspension strut Removal Remove the front wheel. Without using excessive force, disconnect the brake hose holder and wheel speed sensor connector from...

Disassembly and assembly of the front suspension strut
Disassembly Remove the protective cover using a flat-blade screwdriver. Suspension Spring Compressor Using tool J38402, A20, compress the suspension spring until almost...

Front suspension arm — removal and installation
Front suspension arm: 1 – transverse stabilizer bar; 2 – brake disc; 3 – steering rod; 4 – suspension arm; 5 – subframe; 6 - crossbar stabilizer bar Removal Remove the...

Transverse stabilizer bar
Anti-roll bar: 1 – stabilizer bar bracket; 2 – stabilizer bar silent block; 3 – stabilizer bar; 4 – front suspension strut; 5 - transverse stabilizer bar; 6 – stopper; 7...

Front suspension subframe
Stretcher: 1 - transverse stabilizer bar; 2 – rear balance beam support bracket for engine mount; 3 – subframe; 4 – suspension arm. Removal Loosen the bolts securing the...

Front suspension strut — removal and installation
Removal 1. Remove the front wheel. 2. Separate the brake hose bracket and ABS sensor connector from the front suspension strut. 5. Unscrew the nuts, remove the bolts...

Lower control arm front suspension — removal and installation
Removal 1. Remove the front wheel. 2. Loosen the nut and use puller 09568–34000 to press out the ball joint pin of the steering tie rod end from the steering knuckle. 4....

Front stabilizer bar
Removal 1. Remove the front wheel. 2. Remove the stabilizer link. If there are cracks in the protective boot, replace it and add grease to the joint. Rock the stabilizer...

Replacing the ball joint and protective cover of the front suspension strut
Removal the ball joint and protective cover Protective cover of the ball joint of the suspension arm: 1 - retaining ring; 2 – case; 3 – screwdriver Remove the ball joint...

Removal the hub and replacing the hub bearing
Removal the hub Remove the front wheel. Knock out the cotter pin and unscrew the front wheel hub mounting nut. Remove the caliper assembly with the pad guide and brake...

Engine subframe — removal and installation
Removal 1. Unscrew the bolts securing the silent blocks of the lower arm of the front suspension. 2. Remove the exhaust pipe. 3. Remove the rear engine roller support...

Rear Suspension Specifications
Rear suspension elements: 1 - wheel hub; 2 - rear suspension beam mounting bracket; 3 - shock absorber; 4 - rear suspension beam; 5 - spring; 6 - upper suspension spring...

Rear suspension strut
Removal 1. Remove the rear wheel.

Rear suspension shock absorber
Rear suspension shock absorber and its parts: 1 - shock absorber; 2 - lower shock absorber mounting bolt; 3 - casing; 4 - shock absorber compression stroke buffer; 5 -...

Rear suspension spring
Removal 1. Remove the rear wheel. 2. Remove the brake hose mounting bracket. 4. Remove the bolt securing the rear suspension beam to the bracket and the three bolts...

Front wheel alignment angles
Checking the front and rear wheel alignment angles of the Hyundai Getz should be done on a special stand, while the car should be in a horizontal position with the front...

Tire wear
1. Measure the tire tread depth. Minimum permissible tire tread depth: 1.6 mm 2. If the remaining tread depth is less than 1.6 mm, replace the tire. Note: When the tire...

Checking wheel runout
1. Raise the vehicle and secure it on supports. 2. Use a dial indicator to measure the wheel runout. 3. Replace the wheel if the wheel runout exceeds the maximum...

Tightening the wheel nuts
1. Tightening torque for wheels with steel and aluminum disks: 90–110 Nm. Caution! The final tightening torque must be carried out using a torque wrench. 2. Sequence of...

Wheel rotation
1. Rearrange the wheels in accordance with the order shown in the figure. Note: When rotating wheels, the spare wheel should not be used.

Checking the vehicle's drift and directional instability
1. If the vehicle constantly pulls to one side while driving on a level section of road, perform the following checks. Troubleshooting Sign Probable cause Method of...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

We recommend other sections on the topic of Hyundai manuals:

Chassis: Car suspension Hyundai Accent 1 (1994-1999)
Chassis: Car suspension Hyundai Elantra 3 (2000-2006)
Chassis: Suspension and wheels Hyundai Santa Fe 2 (2007-2012, petrol)
Chassis: Car suspension Hyundai Tucson 1 (2005-2010)
Chassis: Suspension and wheels Hyundai Matrix (2001-2010, petrol)

Add to social network:

Link in different formats to this section

TextHTMLBB Code