Car suspension Hyundai Elantra 3

Technical data of suspension
Front suspension Data Meaning Type MacPherson with coil spring Front suspension shock absorber Data Meaning Type Gas Stroke, mm 163,8 Damping at acceleration 0.3 m/s -...

Front suspension strut
Removal 1. Remove the front wheel. 2. Separate the brake hose bracket from the front suspension strut. Caution: Do not tear or damage the brake pipe. 3. Unscrew the nuts...

Lower control arm of the front suspension
Removal 1. Remove the front wheel. 2. Remove the cotter pin from the drive shaft, unscrew the nut and remove the washer securing the shaft to the front wheel hub. 3....

Front stabilizer bar
Removal 1. Remove the front wheel. 2. Remove the stabilizer link. 3. Remove the stabilizer bracket and bushing. 4. Remove the rear engine mount. 5. Remove the anti-roll...

Rear suspension strut
Removal 1. Fold the rear seat. 2. Unscrew the three nuts of the upper rear pillar mount. 3. Remove the rear wheel. 4. Disconnect the brake pipe and wheel speed sensor...

Rear suspension wishbones
Removal 1. Remove the rear wheel. 2. Disconnect the anti-roll bar link. 3. Remove the bolts and the rear suspension trailing arm. 4. Remove the bolt securing the rear...

Rear suspension trailing arms
Removal 1. Disconnect the parking brake cable from the rear suspension trailing arm. 2. Remove the bolts and the rear suspension trailing arm. Disassembly 1. Install the...

Rear stabilizer bar
Removal 1. Remove the anti-roll bar link. 2. Loosen the bolts and remove the rear anti-roll bar mounting brackets. 3. Remove the anti-roll bar. Examination Check the...

Front wheel alignment angles
Checking the front wheel alignment angles must be carried out on a stand, while the car must be in a horizontal position with the front wheels set for straight-ahead...

Tire wear
Measure the tread depth of your tire. Minimum permissible tire tread depth: 1.6 mm. If the remaining tread depth is less than 1.6 mm, replace the tire. Attention! When...

Wheel rotation
Rearrange the wheels in accordance with the order shown in the figure. Caution: When rotating wheels, the spare wheel must not be used.

Checking the vehicle's drift and directional instability
If your vehicle continually pulls to one side while driving on a level section of road, perform the following checks. a. Reverse the front wheels and road test. b. If...

Wheel beating
Procedure 1. Raise the vehicle and secure it on supports. 2. Use a dial indicator to measure the wheel runout. 3. Replace the wheel if the wheel runout exceeds the...

Tightening the wheel nuts
Tightening torque for wheels with steel and aluminum rims: 90–110 Nm. Warning! The final tightening torque must be applied using a torque wrench. Wheel nut tightening...

Troubleshooting suspension problems
Sign Probable cause Method of elimination Tight steering Front wheel alignment is incorrectly adjusted Adjust the front wheel alignment angles Excessive resistance to...

Tire wear diagnostics
Wear of the central part of the tread Very high tire pressure Wear of the central part of the tread down to the cord due to high tire pressure Wear of both side parts of...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

We recommend other sections on the topic of Hyundai manuals:

Chassis: Car suspension Hyundai Accent 1 (1994-1999)
Chassis: Suspension and wheels Hyundai Getz (2002-2011)
Chassis: Suspension and wheels Hyundai Santa Fe 2 (2007-2012, petrol)
Chassis: Car suspension Hyundai Tucson 1 (2005-2010)
Chassis: Suspension and wheels Hyundai Matrix (2001-2010, petrol)

Add to social network:

Link in different formats to this section

TextHTMLBB Code

Elantra 3 (2000-2006)