Brake system of the car Hyundai Getz

Brake system specifications
Front brake mechanism Front wheel brake mechanism: 1 - guide pin; 2 - support; 3 - brake pads; 4 - brake hose; 5 - air release valve; 6 - guide pin; 7 - brake shield; 8...

General information about the brake system
Hyudai Getz vehicles are equipped with a hydraulic brake system, which operates as follows: the brake pedal is connected to the master cylinder; when the pedal is...

Brake system malfunctions
Sign Probable cause Method of elimination Noise or vibration when braking The caliper or brake shield is installed incorrectly Install the caliper or brake shield...

Checking and adjusting the brake pedal height
1. Remove the floor carpet and measure the brake pedal installation height above the floor. If the pedal installation height is not as specified, adjust as follows....

Checking the technical condition and operability of the brake system components
Checking the hydraulic brake drive With the engine running, press the brake pedal with a force of approximately 120 kgf. Check the master cylinder, brake hydraulic drive...

Checking the brake booster
To easily test the brake booster on your Hyundai Getz, perform the following tests. 1. Start the engine and stop it after 1-2 minutes. Press the brake pedal several...

Checking the one-way valve of the brake booster
When testing a one-way valve, the valve must be in the vacuum hose. 1. Remove the vacuum hose. Note: The one-way valve is pressed into the vacuum hose at a certain...

Bleeding the hydraulic brake drive system
1. Remove the cap from the expansion tank and fill it with brake fluid. Caution! Brake fluid dissolves paint, plastic and wire insulation, so if the fluid accidentally...

Adjusting the parking brake stroke
1. After bleeding the hydraulic drive of the Hyundai Getz brake system, press the brake pedal 20 times with a force of more than 10 kg. 2. Tighten the parking brake...

Vacuum brake booster — removal and installation
Removal Attention! When removing the master cylinder, avoid bending or damaging the brake pipes. Brake fluid dissolves paint, plastic and wire insulation, so if the...

Master brake cylinder
Master Brake Cylinder: 1 - brake and clutch hydraulic fluid reservoir cap; 2 - filter; 3 - brake and clutch hydraulic fluid reservoir; 4 - sealing gasket; 5 - piston of...

Pressure regulator — check
The pressure regulator regulates the pressure in the rear brake drive depending on the load on the rear axle of the vehicle. As the load increases, it ensures the...

Brake pipes — removal and installation
Removal Caution! Brake fluid dissolves paint, plastic and wire insulation, so if the fluid accidentally gets on the car's paintwork or its components, wash them with...

Brake pedal — removal and installation
Removal 1. Remove the brake light switch. 2. Remove the cotter pin and push rod axle. 3. Unscrew the flange nuts securing the brake pedal bracket. 4. Remove the brake...

Replacing the front brake pads
This is what the front brake pads look like: A - inner brake shoe; B - wear indicator; B - outer brake shoe Removal 1. Remove the lower guide pin mounting bolt, lift the...

Front Brake Caliper — Removal and Installation
Removal 1. Remove the front wheel. 2. Remove the hollow bolt and disconnect the brake hose from the caliper. Attention! Brake fluid dissolves paint, plastic and wire...

Replacing rear brake pads (drum brakes)
Removal 1. Release the parking brake. 2. Remove the wheel, unscrew the screw and remove the brake drum. 4. Remove the brake shoe support bracket clamps, hold-down...

Replacing the working brake cylinder
1. Remove the brake pads. 2. Disconnect the brake pipe. 3. Unscrew the bolts and remove the wheel cylinder. 4. Remove the dust boots from the wheel cylinder. 7. Before...

Parking handbrake — removal and installation
Parking brake drive: 1 - brake mechanism shield; 2 - left rear wheel brake drive cable; 3 - parking brake system drive lever casing; 4 - parking brake system drive...

Anti-lock braking system (ABS) controls
The anti-lock braking system (ABS) controls the pressure in the hydraulic brake drive of each wheel individually and reduces the fluid pressure in the wheel brake...

Error codes using the Hi-Scan (pro) device
1. Turn off the ignition. 2. Connect the Hi-Scan (pro) device to the diagnostic connector located under the lower trim of the instrument panel. 3. Turn on the ignition....

Hydraulic unit HECU (Hydraulic Electronic Control Unit)
Removal 1. Remove the air filter and air intake pipe. 4. Remove the bracket mounting bolts and remove the HECU unit together with the bracket. Attention! 1. Do not...

Wheel speed sensor (ABS)
Front wheel speed sensor 1. Remove the front wheel speed sensor mounting bolt. Rear wheel speed sensor 1. Disconnect the rear wheel speed sensor electrical connector...

Bleeding the hydraulic brake system using a scanner
Any hydraulic system will operate properly if the air is removed from it. 1. Remove the cap from the expansion tank and fill it with brake fluid. Warning! Brake fluid...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

We recommend other sections on the topic of Hyundai manuals:

Chassis: Brake system Hyundai Accent 1 (1994-1999)
Chassis: Brake system Hyundai Elantra 3 (2000-2006)
Chassis: Brake system Hyundai Sonata 4 (2001-2012, petrol)
Chassis: Brake system Hyundai Santa Fe 2 (2007-2012, petrol)
Chassis: Brake system Hyundai Tucson 2 (2009-2015)
Chassis: Brake system Hyundai Matrix (2001-2010, petrol)

Add to social network:

Link in different formats to this section

TextHTMLBB Code