Brake system of the car Hyundai Santa Fe 2

Checking and adjusting the brake pedal
Fig. 6.1. Adjusting the brake light switch Rotate the brake light switch until the gap between the switch housing and the brake pedal lever reaches the nominal value....

Checking the operation of the brake booster without a tester
Run the engine for one or two minutes and then turn it off. Press the brake pedal several times with the usual force when braking. If the first time you press the brake...

Bleeding the brake hydraulic system
Fig. 6.4. Brake fluid reservoir Remove the brake fluid reservoir cap and fill the reservoir with brake fluid (Fig. 6.4). Caution: If brake fluid comes into contact with...

Removal, checking and installation the brake pedal
Fig. 6.7. Brake pedal Removal Remove the brake light switch. Remove the cotter pin and pull out the tie rod pin. Loosen the brake pedal bracket mounting nuts. Fig. 6.8....

Disassembly, inspection, assembly and installation of the master brake cylinder
Fig. 6.11. Master brake cylinder Removal Disconnect the brake fluid level sensor connector. Disconnect the brake pipes from the master cylinder. Install plugs on the...

Rear brake pressure regulator
The rear brake pressure regulator distributes the correct brake fluid pressure to the front and rear brake circuits to achieve high braking efficiency and prevent rear...

Removal, checking and installation front brake pads
Removal Fig. 6.22. Front disc brake: 1 – connecting tube (brake hose and tube assembly); 2 – front brake caliper assembly; 3 – brake disc The components of the front...

Disassembly and assembly of front disc brakes
Fig. 6.32. Front disc brake components: 1 – guide pin; 2 – guide pin; 3 – bushing; 4 – caliper bracket (with brake pads); 5 – anther; 6 – boot clamp; 7 – piston dust...

Disassembly and assembly of rear disc brakes
Fig. 6.38. Rear disc brake components: 1 – guide pin; 2 – guide pin; 3 – bushing; 4 – caliper bracket (with brake pads); 5 – anther; 6 – boot clamp; 7 – piston dust...

Removal, checking and installation rear drum brakes
Fig. 6.46. Rear drum brakes Removal Remove the rear wheel. Fig. 6.47. Rear wheel hub Loosen the mounting nut and remove the hub together with the brake drum (Fig. 6.47)....

Checking and adjusting the travel of the parking brake lever
Apply approximately 196 N of force to the parking brake lever and count the number of clicks. The parking brake lever travel is 7 clicks. Fig. 6.8. Pedal assembly with...

Anti-lock braking system
Fig. 6.56. Location of system components The anti-lock braking system (ABS) controls the pressure in the brake circuits of all four wheels when braking on dangerous...

Removal and installation the ABS electronic control unit
Fig. 6.60. ABS electronic control unit Removal Fig. 6.61. ABS integrated control unit connectors Disconnect the connectors from the ABS Integrated Control Unit (HECU)...

Checking the ABS hydraulic unit
Fig. 6.62. Brake pipes of the ABS hydraulic unit Caution! Before connecting (or disconnecting) the Hi-Scan tester, turn the ignition key to the "OFF" position....

Removal and checking wheel speed sensors (ABS)
Fig. 6.63. Location of ABS wheel speed sensors Removal Fig. 6.64. Sensor mounting bolt Loosen the wheel speed sensor mounting bolt (Fig. 6.64). Fig. 6.65. Wheel speed...

Checking the operation of the ABS system
Checking the voltage of the wheel speed sensor signal Raise the vehicle and release the parking brake. Disconnect the ABS Integrated Control Unit (HECU) connectors and...

Table 6.1. Technical characteristics (main brake system)
Technical specifications (main brake system)

Table 6.2. Basic data for adjustments and control
Basic data for adjustments and control Parameter Nominal value Brake pedal height above the floor 208 (+5.0) mm Gap between brake pedal and brake light switch housing...

Table 6.3. Tightening torques for threaded connections (main brake system)
Tightening torques for threaded connections (main brake system) Component Tightening torque, Nm Nut securing the master brake cylinder to the brake booster 8-12 Brake...

Table 6.4. Possible malfunctions, their causes and methods of elimination
Possible malfunctions, their causes and methods of elimination

Table 6.5. Technical characteristics (ABS system)
Technical specifications (ABS system)

Table 6.6. Tightening torques for threaded connections (ABS)
Tightening torques for threaded connections (ABS) Component Tightening torque, Nm Wheel speed sensor mounting bolt - For the front wheel 0,4-0,6 - For the rear wheel...

Table 6.7. Voltage table at the terminals of the ABS control unit
Table of voltage at the terminals of the ABS control unit

Table 6.8. Some phenomena occurring during diagnostics of the ABS system
Some phenomena occurring during diagnostics of the ABS system Phenomenon Explanation of the phenomenon Sound when checking the system's functionality When starting the...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

We recommend other sections on the topic of Hyundai manuals:

Chassis: Brake system Hyundai Accent 2 (1999-2005)
Chassis: Brake system Hyundai Elantra 3 (2000-2006)
Chassis: Brake system Hyundai Getz (2002-2011)
Chassis: Brake system Hyundai Sonata 3 (1993-1998)
Chassis: Brake system Hyundai Tucson 2 (2009-2015)
Chassis: Brake system Hyundai Matrix (2001-2010, petrol)

Add to social network:

Link in different formats to this section

TextHTMLBB Code

Santa Fe 2 (2007-2012, petrol)