Brake system of the car Hyundai Accent 1

Technical characteristics of the brake system
Master Brake Cylinder: Inner diameter - 20.64 mm Brake Fluid Level Sensor - Yes Brake Booster - Vacuum Gain Ratio: 4.0:1 Front brake: Type - Disc with floating caliper...

Brake system malfunctions
Possible malfunctions of the brake system, their causes and methods of elimination.

Adjusting the brake pedal
1. Pedal height. Height from top of pedal to floor "A" - 163-168 mm If the pedal height does not match this value, adjust according to the following recommendations. 1)...

Brake booster test
A simplified method for checking the operation of the brake booster is to perform the following operations. 1. Let the engine run for 1 or 2 minutes and then turn it...

Bleeding the brake system
1. Unscrew the brake reservoir cap and fill it with brake fluid. Warning: Do not allow brake fluid to come into contact with painted surfaces of the vehicle. Rinse the...

Adjusting the travel of the parking brake lever
1. Press the brake pedal 20 times with a force of about 196 N (20 kgf). 2. Pull the parking brake lever towards you with a force of approximately 196 N (20 kgf) and...

Brake pedal — device
Tightening torques: Nm (kgf cm, lb ft)

Master brake cylinder — device
Tightening torques: Nm (kgf cm, lb ft)

Brake booster — device
Tightening torques: Nm (kgf cm, lb ft)

Brake lines — device

Dosing valve
Note: Do not disassemble the valve. It regulates the distribution of fluid under pressure between the front and rear brakes to prevent slippage in the event of wheel...

Front disc brake — device
Tightening torques: Nm (kgf cm, lb ft)

Brake pads — removal, inspection and installation
The brake pads are equipped with wear indicators, which, when they reach a thickness of 2 mm, begin to contact the brake disc, producing a screeching sound that warns...

Support — removal, inspection and assembly
Removal 1. Remove the wheel with the tire. 2. Disconnect the brake hose. Note: To prevent fluid from leaking, plug the brake hose. 3. Remove the cylinder mounting bolt....

Rear Drum Brake — Removal, Checking and Installation
Tightening torques: Nm (kgf cm, lb ft) Removal 1. After the wheel has been removed, remove the brake drum. 2. Remove the shoe spring, the automatic adjusting mechanism...

Parking brake lever — device
Tightening torques: Nm (kgf cm, lb ft)

General information about the anti-lock braking system
Anti-lock Brake System (ABS) Control Module: Operating voltage range: 9.0-16.2 V Current consumption is 150 mA or less Fuse - 3A Operating temperature range: from -40°...

Components of the ABS system

ABS modulator and relay — removal and installation
Tightening torques: Nm (kgf cm, lb ft) Removal 1. Remove the right front turn signal. 2. Disconnect the ABS relay connector inside the fender. 3. Disconnect the pump...

ABSCM (ABS Control Module) — Removal
1. Remove the interior trim on the right side of the trunk. 2. Remove the ABSCM control module mounting bolts and the module itself.

Wheel speed sensor
Tightening torques: Nm (kgf cm, lb ft)

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

We recommend other sections on the topic of Hyundai manuals:

Chassis: Brake system Hyundai Elantra 2 (1995-2000, petrol)
Chassis: Brake system Hyundai Getz (2002-2011)
Chassis: Brake system Hyundai Sonata 4 (2001-2012, petrol)
Chassis: Brake system Hyundai Santa Fe 2 (2007-2012, petrol)
Chassis: Brake system Hyundai Tucson 2 (2009-2015)
Chassis: Brake system Hyundai Matrix (2001-2010, petrol)

Add to social network:

Link in different formats to this section

TextHTMLBB Code