Removal, installation and adjustment of a sound signal Withdrawal 1. Remove the grille. 2. Unscrew the screw, disconnect the connector and remove the horn (A). Installation 3. Installation is carried out in the reverse order...
Removal and installation of the switching unit Withdrawal 1. Disconnect a wire from the negative plug of joint stock bank. 2. Remove the dashboard trim on the driver's side (1). 3. Turn off two nuts, disconnect...
Removal and installation of the fuse box in the cabin Withdrawal 1. Disconnect a wire from the negative plug of joint stock bank. 2. Remove the driver's side lower shelf (1). 3. Disconnect the junction block connectors and...
Relay test Type A Apply battery voltage to relay pins 3 and 4 and check continuity between pins 1 and 2. If no power is applied, the circuit should be open. A. Fog lamp relay; B....
Checking the integrated relay box Integral relay (A) integrates alarm relay, anti-theft alarm relay and anti-theft siren relay in a single housing. 1. Alarm relay: connect «+» And «-» battery with...
Removal and installation of a combination of devices Withdrawal 1. Disconnect a wire from the negative plug of joint stock bank. 2. Remove the instrument panel bezel (1), unscrewing the screws, disconnecting the connector...
Testing instrumentation Speedometer 1. Check tire pressure and correct if necessary. 2. Install the front wheels of the car on the running drums. Be sure to install wheel chocks under the rear...
Removal, installation and check of the ignition lock Withdrawal 1. Disconnect a wire from the negative plug of joint stock bank. 2. Remove the bottom panel from the driver's side. 3. Remove the screw, disconnect the...
Audio system. Removal and installation. 1. Audio system; 2. Amplifier; 3. High frequency speaker; 4. External antenna; 5. Front speaker; 6. Rear speaker (sedan); 7. Rear speaker (hatchback); 8. Antenna wire...
Removing and installing the front speaker Withdrawal 1. Remove facing of a forward door. 2. Remove the four screws and remove the front speaker (A). Installation 3. Installation is carried out in the reverse...
Removal and installation of the rear speaker Withdrawal For sedan models only 1. Remove the rear seat. 2. Remove facing of a back shelf. 3. Unscrew the four screws and remove the rear speaker (A). Only for...
Removing and installing a tweeter Withdrawal 1. Remove facing of a forward door. 2. Disconnect the connector (A), remove the screws and remove the tweeter. Installation 3. Installation is carried out in...
Removal and installation of the amplifier Withdrawal For sedan models only 1. Remove the lining of the trunk on the right side. 2. Unscrew the three nuts and remove the amplifier (IN) from the body (A). Only for...
Removing and installing an external antenna Withdrawal 1. Lower the back of the headlining down. 2. Disconnect the connector (A) and cable (IN) from the antenna. Loosen the nut and remove the antenna. Installation...
Checking the Antenna Cable 1. Disconnect the cable from the antenna and audio system. 2. Check the integrity of the central core of the cable. If the circuit is open, replace the cable. 3. Check...
Checking the door lock drive and switch 1. Remove facing of a door. 2. Disconnect the connector from the lock drive. 3. Apply battery voltage to the connector contacts and check the operation of the lock...
Checking the tailgate limit switch 1. Disconnect a wire from the negative plug of joint stock bank. 2. Remove the lining of the trunk lid and the limit switch. Disconnect the connector from the rear...
Checking the door switch Remove the limit switch and check the circuit between the connector pins.
Checking the hood limit switch 1. Disconnect the connector from the switch. 2. Check up a chain between an output and a body at various statuses of the switch. Checking the hood contact switch
Checking the ignition switch 1. Unscrew the three screws and remove the steering column covers (A). 2. Disconnect the connector from the ignition switch. 3. Check up a chain between contacts of a...
Siren check 1. Loosen the screw, disconnect the connector and remove the siren. 2. Apply battery voltage to pin 1 and ground pin 2 of the connector. Make sure the siren is working...
Checking the door lock switch 1. Disconnect a wire from the negative plug of joint stock bank. 2. Remove facing of a door of the driver. 3. Disconnect the connector from the switch. 4. Check up a...
Check of the switch of position and heating of mirrors 1. Remove facing of a door of the driver. 2. Disconnect the connector from the switch. 3. Check up continuity of a chain between the corresponding contacts of a socket...
Check of a drive and a heater of an external mirror 1. Remove two screws (IN) and remove the cover (A). 2. Remove the tweeter. 3. Disconnect a socket of a drive of an external mirror. 4. Apply battery voltage to the...
Checking the power window motor 1. Remove facing of a door. 2. Disconnect the power window motor connector. 3. Connect the connector pins directly to the battery and check the operation of the electric...
Checking the Power Window Master Switch 1. Disconnect a wire from the negative plug of joint stock bank. 2. Remove facing of a door of the driver. 3. Disconnect the switch connector. 4. Check up circuit...
Checking the auxiliary power window switch 1. Disconnect a wire from the negative plug of joint stock bank. 2. Remove facing of a door. 3. Disconnect the switch connector. 4. Check up circuit closure between the...
Checking the rear window heater Caution: wrap thin foil around the voltmeter probe. Use your finger to press the foil against the conductor and move it along the conductor to locate the open circuit....
Rear window heater repair 1. Clean the glass area around the broken heating element. 2. Apply protective tape along the damaged area of the heating filament. 3. Shake the conductive paint can...
Checking the heated rear window switch 1. Disconnect a wire from the negative plug of joint stock bank. 2. Remove the cladding (1). Disconnect connectors (2) rear window heating switches and hazard warning...
Check of the relay of a heater of back glass 1. Disconnect a wire from the negative plug of joint stock bank. 2. Remove the fuse and relay box in the passenger compartment. 3. Check up continuity of a chain between...
Location of windshield wiper and washer 1. Lever and wiper blade; 2. Wiper and washer control switch; 3. Washer hose; 4. Windshield wiper with electric motor; 5. Washer pump; 6. Washer fluid reservoir
Checking the wiper motor Windshield wiper Speed test 1. Disconnect the wiper motor connector. 2. Connect «+» And «-» battery to pins 6 and 5 of the connector, respectively. Make sure the motor...
Removal, installation and check of the washer pump Withdrawal 1. Disconnect a wire from the negative plug of joint stock bank. 2. Remove the front bumper. 3. Disconnect the hose and connector from the pump (A). Loosen...
Checking the seat heating switch 1. Disconnect a wire from the negative plug of joint stock bank. 2. Use a screwdriver to unhook the grips and remove the seat heating switches. 3. Using an ohmmeter,...
Checking the seat heater 1. Disconnect the heater connector and measure the resistance between pins 1 and 3. Rated value: 2.31 ohms±10% (pillow - 1.15 Ohm; back - 1.16 Ohm). 2. Connect the...
Checking the sunroof switch 1. Disconnect a wire from the negative plug of joint stock bank. 2. Open the glasses compartment and unscrew the two screws. 3. Disconnect the connector and remove the...
Removal, installation and check of the sunroof motor Withdrawal 1. Disconnect a wire from the negative plug of joint stock bank. 2. Remove the three screws, disconnect the connector and remove the motor (A). Installation...
Outdoor and indoor lighting system 1. Headlight lamp (near/far light); 2. Front turn signal; 3. Parking lamp; 4. Turn signal repeater; 5. Fog lamp; 6. Trunk lighting; 7. Brake/side lamp; 8. Rear turn...
Removal and installation of the block headlight Withdrawal 1. Disconnect a wire from the negative plug of joint stock bank. 2. Turn off the screw, unhook capture and remove a radiator lattice. 3. Unscrew the headlight...
Removal and installation of a fog lamp Withdrawal 1. Disconnect a wire from the negative plug of joint stock bank. 2. Loosen the screws, disconnect the connector (A) and remove the fog lamp (IN). Note: To...
Headlight adjustment Dimensions for installing the car in front of the screen H1: Distance from road surface to headlight bulb centers (near/far light) H2: Distance from the road surface to...