Car automatic transmission Hyundai Accent 3

Technical characteristics of automatic transmission
Tightening torques for threaded connections Location of automatic transmission control system components 1. Speedometer sensor; 2. Output shaft speed sensor; 3. Input...

Checking the input and output signals of the automatic transmission control unit
Note: The test is performed from the wiring harness side with the connector connected.

Checking the elements of the automatic transmission control system
Note: Checking the elements of the automatic transmission control system is performed using a diagnostic tester.

Checking the main pressure
1. Warm up the engine to the operating temperature of the transmission fluid (80-100C). 2. Raise the vehicle so that the wheels can turn freely. 3. Connect the...

Checking the maximum engine speed with the torque converter locked (STALL TEST)
1. Check the transmission fluid level. 2. Warm up the transmission fluid to operating temperature (80-90C). Note: The transmission fluid warms up to operating...

Removal and installation of automatic transmission
List of elements for the drawings 1. Torque converter; 2. Gearbox support bracket; 3. Washer; 4. Front powertrain support bracket; 5. Washer; 6. Gearbox housing; 7....

Adjusting the low gear switch
Note: If the low range switch does not function properly, adjust it: oN - 1st or 3rd gear; off (OFF) - 2nd or 4th gear. Checking the switch is described in the section "...

Checking the electromagnetic valves
Description Designation Purpose Torque converter lock-up valve DCCSV Controls the engagement of the locking clutch Shift control valve A SCSV-A Controls the engagement...

Main line pressure adjustment
1. Drain the transmission fluid. 2. Remove the oil pan (1). Tightening torque: 10-12Nm. 3. Remove the oil filter (2). 4. Remove the transmission fluid temperature sensor...

Adjustment of pressure reducing
Without using a diagnostic tester 1. Remove all components up to the oil filter, as for the case of adjusting the main pressure (the valve assembly does not need to be...

Checking the shaft speed sensors
Examination 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the air intake duct and air filter. 3. Disconnect the sensor wire from the cable...

Checking the transmission fluid temperature sensor
Examination 1. Disconnect the wire from the negative terminal of the battery. 2. Raise the car. 3. Remove the engine side splash shield. 4. Disconnect the transmission...

Checking the automatic transmission selector position sensor
1. Set the selector lever to position "P" or "N" and make sure that the engine does not start when the ignition key is in the Start position. 2. Check that the reversing...

Removal and installation the automatic transmission selector lever
1. Selector cable 2. Selector lever lock cable 3. Selector lever assembly 4. Automatic transmission selector lever Removal 1. Remove the floor console. 2. Disconnect the...

Disassembling and assembling the selector lever
1. Support bracket; 2. Selector lever; 3. Spring lock; 4. Axial pin; 5. Washer; 6. Cable bracket; 7. Screw; 8. Nut; 9. Cover with lever position indicator; 10. Lever...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

We recommend other sections on the topic of Hyundai manuals:

Transmission: Automatic gearbox Hyundai Elantra 3 (2000-2006)
Transmission: Automatic gearbox Hyundai Getz (2002-2011)
Transmission: Automatic gearbox Hyundai Sonata 4 (2001-2012, petrol)
Transmission: Automatic gearbox Hyundai Santa Fe 2 (2007-2012, petrol)
Transmission: Automatic gearbox Hyundai Tucson 2 (2009-2015)
Transmission: Automatic gearbox Hyundai Matrix (2001-2010, petrol)

Add to social network:

Link in different formats to this section

TextHTMLBB Code