Vehicle power and exhaust system Hyundai Accent 3

Removal and installation the intake manifold
1. Intake manifold 2. Throttle assembly 3. Idle speed control 4. Fuel manifold 5. Screw 6. Cylinder head 7. Intake manifold stand Removal 1. Remove the engine cover. 2....

Removal and installation the exhaust manifold
1. Cylinder head 2. Heat shield 3. Gasket 4. Exhaust manifold Removal 1. Remove the engine cover. 2. Disconnect the front oxygen sensor connector. 3. Remove the front...

Removal and installation the muffler
1. Front muffler 2. Intermediate muffler 3. Main muffler Removal 1. Remove the front muffler heat shield (1). Tightening torque of screws: 8-12 Nm. 2. Remove the front...

Toxicity reduction system
Note: The design and location of individual elements of the toxicity reduction system may differ from those shown depending on the sales market and vehicle...

Checking the fuel vapor recovery system
1. Disconnect the vacuum hose from the throttle body and connect a vacuum pump to the hose. 2. Check the fuel vapor recovery system on a cold (coolant temperature no...

Removal and installation the crankcase ventilation valve
Removal 1. Remove the engine cover and disconnect the vacuum hose (B). Remove the valve (A) from the cylinder head cover. Examination 2. Insert a thin rod (A) into the...

Checking the absorber purge valve
Note: Before disconnecting the hose, mark its position for subsequent reconnection. 1. Disconnect the valve vacuum hose. 2. Disconnect the valve connector. 3. Connect...

Checking the carbon absorber
1. Remove the absorber and check the housing for cracks or damage. 2. Bring air into the fitting (1) (fuel tank) and make sure that it comes out through fittings (2)...

Elements of the engine power supply system
1. Fuel tank 2. Fuel pump 3. Carbon absorber 4. Filler neck 5. Drainage hose 6. Air filter 7. Tube (tank ↔ absorber) 8. Tube (absorber ↔ intake manifold) 9. Hose...

Checking fuel pressure
1. Fold the rear seat forward. 2. Remove the fuel pump cover (A). 3. Disconnect the fuel pump connector (B). 4. Start the engine and wait until the engine fuel hose is...

Checking the fuel injector
1. Remove the nozzle. 2. Measure the resistance of the injector solenoid valve winding. Nominal value: 13.8-15.2 Ohm. If the measured value is not corresponds to the...

Removal and installation the fuel pump
Removal 1 Fold the rear seat forward. 2. Remove the fuel pump cover (1). 3 Disconnect the fuel pump wiring connector (2). 4. Start the engine and wait until the fuel...

Removal and installation the fuel tank
Removal Note: The fuel tank removal procedure is described for the case with the fuel pump removed. 1. Raise the vehicle. 2. Remove the intermediate muffler. 3. Support...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

We recommend other sections on the topic of Hyundai manuals:

Power unit: Fuel system (diesel) Hyundai Elantra 3 (2000-2006)
Power unit: Fuel system Hyundai Getz (2002-2011)
Power unit: Fuel system Hyundai Sonata 3 (1993-1998)
Engine 2.0 and 2.4 liters: Fuel system Hyundai Santa Fe 2 (2007-2012, petrol)
Power unit: Engine power system Hyundai Tucson 2 (2009-2015)
Power unit: Power and exhaust system Hyundai Matrix (2001-2010, petrol)

Add to social network:

Link in different formats to this section

TextHTMLBB Code